View TD1311AF_2040519.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 03.05.2005 rf solutions objective specification td1300a(l)f mk3 tuner modules for analog and digital terrestrial (ofdm) applications approved by : name / date :
philips rf solutions objective specification 2 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 features ? highly integrated single conversion tuner with active loopthrough ? versions for different frequency ranges available ? +5v supply voltage only; no exte rnal tuning voltage required ? dc ? power output through rf-input connector (e.g. indoor antenna supply) ? superior low noise and high sensitivity performance ? tuners are suitable for anal og and digital applications; ? compliant to relevant standards e.g. cenelec and nordig ? tuners are available in vertical and horizontal mounting ? small size (50mm x 44mm x 14mm) ? rf-in to rf-out loopthrough amplifiers ? low noise and excellent linearity ? full vhf to uhf frequency range coverage ? standard connectors for in- and output e.g. iec, f- and rca-connector on request ? high performance and cost effective single conversion tuner ? i 2 c programmable ? 3.3v and 5v bus compliant with max. 400khz clock ? fast pll tuning speed (programmable step size e.g. 62.5khz and 166.67khz) ? tuner internal gain control loop with selectable takeoverpoint settings via i 2 c bus ? external gain control possible with internal loop disabled ? 4.0v (max. gain) to 0v (min. gain) gain control voltage ? flat overall frequency response ? low phase noise pll ? 4 mhz crystal reference frequency output ? saw-filter and if-amplifier included ? switchable 7/8 mhz or fixed 8mhz saw filter ? if-amplification controllable over a wide range ? differential if-output filtered by saw filt er; can directly drive the channel decoder ? unbalanced (wide-band) if-output for analog applications
philips rf solutions objective specification 3 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 ordering informations type name ordering code specialities with rf-loopthrough td1316alf/ihp-3 tbd horizontal mounting td1316alf/ivp-2 tbd vertical mounting without rf-loopthrough td1316af/ihp-3 tbd horizontal mounting vhf ? uhf full-band pll tuner td1316af/ivp-3 tbd vertical mounting with rf-loopthrough td1311alf/ihp-3 tbd horizontal mounting td1311alf/ivp-3 tbd vertical mounting without rf-loopthrough TD1311AF/ihp-3 tbd horizontal mounting vhf ? uhf 2-band pll tuner TD1311AF/ivp-3 tbd vertical mounting with rf-loopthrough td1344alf/ihp-3 tbd horizontal mounting td1344alf/ivp-3 tbd vertical mounting without rf-loopthrough td1344af/ihp-3 tbd horizontal mounting uhf ? only pll tuner td1344af/ivp-3 tbd vertical mounting
philips rf solutions objective specification 4 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 product description td1300alf-3 belong to the 3 rd generation of terrestrial tuners de signed to cope with digital cofdm and analog transmission standards. from function point-of-view these tuners can be divided into two high-frequency sections, a rf- loopthrough and a single conversion tuner part. in the loopthrough section broadband low-noise amplifiers are used. the loopthrough frequency response covers the entire frequency range from vhf to uhf. the rf-downstream section is equipped with a stat e-of-the-art 3-band single conversion tuner, which makes use of a highly integrated mopll ic that provides the required high level of performance necessary for cofdm signal processing. the tuners are provided with a dc/dc converte r to generate the tuning voltage internally. the internal 4mhz pll crystal reference frequency is fe d through one of the pin-terminals and can be used as a clock for a 2 nd device e.g. the channel decoder. two if-outputs are provided, one is a wideband, non filtered if-output, while the other, narrow-band if-output is equipped with a saw-filter and a gain controllable if-amplifier. this narrow-if-output matches the a-to-d converter input of currently available channel decoders. all tuners out of this family can be equipped with two standard iec-connectors, rf-in is iec-female, rf-out is iec-male. the tuner housing is available in a vertic al or horizontal mountable ex ecution; the pinning pitch corresponds to the world standard pinning convention. apart from the rf-connectors, all other terminals are ma de with wire pins at the bottom side of the tuner. frequency allocation table: td1316a(l)f td1311a(l)f td1344a(l)f rf frequency range 51mhz ? 858mhz ( * ) 174mhz ? 858mhz ( * ) 474mhz ? 858mhz ( * ) channel bandwidth 7/8mhz 7/8 8 mhz rf-loopthrough range ch e2 - ch e69 ch e2 - ch e69 ch e2 - ch e69 if-center frequency 36.13mhz 36.13mhz 36.13mhz rf input connector rf output connector iec female iec male iec female iec male iec female iec male ( * ) data refer to rf-channel center frequency.
philips rf solutions objective specification 5 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 block diagramm td1316a(l)f-3 , td1344a(l)f-3 , td1311a(l)f-3 rf-input rf-output dc-power for indoor antenna (1) saw high-ban d m id-band low-band osc. osc. osc. 33v v 5v tune high mid low +5v tuner supply voltage rf -agc control . mopll pl l ic-bus 2 agc loop ag c loop 4m hz crystal ref erence if - output (broadband) if - agc if - output (narrowband) reference frequency output (6) (7) (2) (4/5) (9) (8) (10/11) . . . .
philips rf solutions objective specification 6 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 definition of terminals / supply data td1316a(l)f / td1344a(l)f / td1311a(l)f terminal function remark 1 dc-power option for tuners with p-extension max. permissible current: 100ma 2 external rf-gain control voltage (0.5v - 4.0v) source impedance limited to 1kohms 3 pll chip address select (i 2 c / tuner) see application notes 4 scl (i 2 c / tuner) 5 sda (i 2 c / tuner) 6 4mhz reference frequency output; ac coupled 7 +5v 5% supply tuner (v tu ) 8 'broadband' if - output ac coupled 9 if-gain control voltage max. gain at 3v min. gain at 0v (see application notes) 10 'narrowband' if - output ac coupled 11 'narrowband' if - output ac coupled 11 10 9 8 71 2 3 4 5 6 . . . .
philips rf solutions objective specification 7 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 ratings environmental conditions symbol parameter conditions min. max. unit non-operational conditions t amb ambient temperature -25 +85 c rh relative humi dity - 95 % g b bump acceleration 25g - 245 m/s 2 g s shock acceleration 50g - 490 m/s 2 vibration amplitude 10 to 55 hz - 0.35 mm operational conditions t amb ambient temperature -10 +60 c rh relative humi dity - 95 % limiting values under operational conditions the tuner can be guaranteed to function properly under the following conditions. symbol parameter pin min typ. max. unit 20 v v l i l dc-loopthrough to input connector (optional) max. permissible current 1 100 ma 4.75 5.00 5.25 v v tu i tu tuner supply voltage relevant supply current 7 - 185 205 ma v ripple max. permissible ripple voltage (50hz ? 100khz) (1) 7 10 (1) mvpp v agc tuner agc voltage - 4.0 4.5 v ? v agc agc voltage range 2 0.3 - 4.0 v
philips rf solutions objective specification 8 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 i agc agc control current - - t.b.f. ma v if-agc if- agc input voltage - 3.0 4.0 v ? v if-agc if- agc input voltage range 9 0 - 3.5 v i if-agc if- agc input current - - 10 a v as address select input voltage 3 - - 5.25 v v scl serial clock input voltage 4 -0.3 - 5.25 v v sda serial data input voltage -0.3 - 5.25 v i sda serial data input current 5 -1 - 5 ma note 1: maximum allowable ripple voltage superimposed on the +5v supply voltage in the frequency range 50hz to 100khz; worst case the combination of tuner plus cofdm channel decoder (e.g. philips semiconductors cofdm reference board om5754) can withstand a max. +5v supply voltage ripple of 10mvpp of which the most sensitive ripple frequency is between 500hz and 1khz. specification criteria is: 8k ofdm, 64qam, ber 2x10 -4 post viterbi
philips rf solutions objective specification 9 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 specification data if not otherwise stated the electrical performance refers to: ? ambient temperature : 22 c 2 c ? relative humidity : 60% 10% ? supply voltages : 5v 0.1v ? rf-gain control voltage : 4.0v 0.1v (internal agc detector disabled; see application notes) ? if-gain control voltage : 1v max. ? rf-input termination : 75 ohms ? rf-output termination : 75 ohms next specification data refer to the overal l performance from rf-input to if-output. if not otherwise stated, all data are assigned to broadband if-output. the tuner has to be tuned as such that coincidence between rf-channel center and if-center frequency of 36.13mhz is given. min. typ. max. frequency ranges (vhf/uhf) (1) (vhf low) low-band (vhf high) mid-band (uhf) high-band uhf only tuners 49mhz 162mhz 448mhz 474mhz 159mhz 444mhz 861mhz 861mhz rf voltage gain (2) 44db 49db overall gain taper 6db rf agc range low band mid band high band 40db 40db 35db image rejection (referred to if-center frequency) (vhf low) low-band (vhf high) mid-band (uhf) high-band 66db 66db 55db 70db 70db 60db osc. voltage at aerial input (f < 1000mhz) <20dbv rf-input return loss (75ohms) 5db >7db in-channel return loss (3) 8db noise figure (at nom. gain) 5db 7db esd protection of terminals 2kv surge protection at rf-input 5kv osc. phase noise (4) (1khz) (10khz) -73dbc/hz -73dbc/hz overall voltage gain (5) 80db note 1: channel center including tuning margin note 2: to be measured at ?broadband? if-output with 1kohms load note 3: to be measured at rf-input in the range channel-center 3mhz note 4: pll step size 166.667khz; cp as recommended (see application notes) note 5: measured at narrow band if-output te rminals 10/11; if-agc voltage (terminal 9) set to 3v
philips rf solutions objective specification 10 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 cross-modulation: definition: the cross-modulation is defined as the transfer of the adjacent channels' modulation depth to the wanted carrier. measurement: unwanted carriers (f unw ) = wanted carrier (f w ) 8mhz level of all carriers = 70dbv modulation = am, 50%, 15khz if-output loaded with 1k ? // 15pf // 1.2uh (load compensation) if-output level limited to 104dbv spec. limit: max. cross-modulation is less or equal 1% (typ. 0.3%) flatness (tilt) of overall responds curve (to be measured at broad-band if-output): definition: tilt of curve is defined in the specified if-range from highest to lowest gain point at nom. gain measured at broadband if-output: in the range if-center 3mhz : 3db max. in the range if-center 4mhz : 4db max. deterioration of flatness during agc (0db to 30db) : 1.0db max. input sensitivity: the typical input sensitivity, when measured in an adequate application (i.e. philips semiconductors cofdm reference board om5754) is: - 82dbm , ber 2x10 - 4 post viterbi conditions: gaussian channel w/o added noise, 8k ofdm, 64qam, code rate 2/3, guard interval 1/8 +6 +2 0 -2 -4 -6 +4 -4 -3.0 +3.0 +4 36.13 mhz db . . . .
philips rf solutions objective specification 11 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 typical response curves at narrowband if-output (tuner set to 470mhz): 7mhz wide saw-filter selected 8mhz wide saw-filter selected (uhf only tuners) 4mhz reference output (terminal 6): frequency accuracy : 80ppm max. max. permissible load : t.b.f. output level : 440mvpp typ. [ 0 c - 60 c ; supply voltage (terminal 7) +5v5% ; loaded with min. t.b.d. ] phase noise @ 1khz : -104dbc/hz typ. next specification data refer to the overall performance from rf-input to rf-output. (valid for all tuners with loopthrough) min. typ. max. frequency range (referred to channel center) 51mhz 858mhz power gain 3db overall gain taper 2.5db noise figure 5db cso / ctb (acc. en50083) -57dbc rf-output return loss (referred to 75 ? ) 10db center 36.13mhz center 36.13mhz 1.5mhz/ 1.5mhz/ span 15mhz span 15mhz 10db/ 10db/ . . . .
philips rf solutions objective specification 12 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 application notes programming of tuner pll the tuner control (frequency selection and band switching) is done via the i 2 c bus. one address byte and four data bytes are needed to fully program the tuner. a pll lock flag can be read from the tuner during 'read' - mode. four independent pll addresses are available; which one is actually valid depends on the address select voltage that is connected to terminal 3. all tuners out of this family are 3.3v and 5v i 2 c bus level compliant. i 2 c-bus data format , ' write ' - mode: name byte msb lsb ack addressbyte 1 1 1 0 0 0 ca1 ca0 r/w=0 a prog. divider byte 1 2 0 n14 n13 n12 n11 n10 n9 n8 a prog. divider byte 2 3 n7 n6 n5 n4 n3 n2 n1 n0 a control data byte 4 1 cp t2 t1 t0 r1 r0 0 a switchport byte 5a 0 0 0 sp4 sp3 sp2 sp1 sp0 a auxiliary byte (*) 5b agc al2 al1 al0 0 0 0 0 a a = acknowledge description of used symbols: ca1, ca0 : chip address selection bits (s ee table: programmable address selection bits) r/w : read / write bit ; bit = 0 ? write mode bit = 1 ? read mode n14 to n0 : lo frequency divider bits cp,t2, t1, t0 : pll charge pump settings; t2, t1, t0 = 0, 1, 1 ? switchport byte (5a) is repl aced by auxiliary byte (5b) r1, r0 : reference divider bits sp4 ..... sp0 : band selection and saw filter switch ports; stand-by on: sp1, sp0 = 1, 1 agc : agc time constant bit; agc = 0 ? low agc current result in high time constant agc = 1 ? high agc current result in low time constant al2, al1, al0 : rf-agc loop t ake o ver p oint (top) bits ca1, ca0: programmable address selection bits ca1 ca0 voltage applied to terminal 3 0 0 0v to 0.1xv tu 0 1 terminal open 1 0 0.4xv tu to 0.6xv tu 1 1 0.9xv tu to 1.0xv tu
philips rf solutions objective specification 13 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 n14 to n0: programmable divider bits divider ratio: n = n14x2 14 + n13x2 13 + ... + n1x2 1 + n0 how to calculate the programmable divider ratio n : ( ) ? ? ? ? ? ? + = hz hz f f f n ref if input whereby [] khz hz f ref 5 . 62 64 10 4 ) 1 ( 6 = ? = [] khz hz f ref 6 6 . 166 24 10 4 ) 1 ( 6 = ? = note (1) : reference divider ratio to be set with bits ' r1/ r0 ' (see table below) do not set the divider ratio as such that the t uner is tuned into extreme conditions i.e. far below or far above the specified ranges. t2, t1, t0: pll charge pump current settings (control data byte) : note: during search tuning it is recommended to set the pll charge pump current to ?low?. after channel acquisition the charge pump current should be set to conditions as indicated in below table. cp t2 t1 t0 pll charge pump oscillator frequency 0 1 1 1 low cp 84mhz < low-band oscillator <180mhz 197mhz < mid-band oscillator <366mhz 484mhz < high-band oscillator <646mhz low-band oscillator >180mhz mid-band oscillator >366mhz 646mhz < high-band oscillator <790mhz 1 1 1 0 medium cp generally recommended for pal applications 1 1 1 1 high cp high-band oscillator >790mhz 0/1 * 0 1 1 auxiliary byte enabled * note: after the cp-bit has been set and th e auxiliary byte is going to be addressed , the cp-bit must remain unchanged ! r1, r0 : pll reference divider settings (control data byte) : pll step size pll ref. divider ratio r1 r0 166.67 khz 24 1 0 62.5 khz 64 1 1
philips rf solutions objective specification 14 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 sp4 ..... sp0: band and saw-filter selection table (switchport byte) : sp4 sp3 sp2 sp1 sp0 low - band 0 x 0 0 1 mid - band 0 x 0 1 0 high - band 0 x 1 0 0 7 mhz saw - filter 0 0 x x x 8 mhz saw - filter 0 1 x x x stand-by mode x x x 1 1 al2, al1, al0 : tuner internal gain control loop settings (auxiliary byte): to have access to the agc loop ? t ake o ver p oint? bits, the control byte bits t2, t1, t0 must be set to 0, 1, 1 . external agc mode: the tuner can be controlled by an external gain control voltage applied to terminal 2 of the tuner. in that case the alx - bits need to be set as shown in table below. al2 al1 al0 agc loop top remarks 0 0 1 high (0db reference) 0 1 0 medium -3db 0 1 1 low -6db range recommended for dvb-t applications 1 0 0 -9db 1 0 1 -12db recommended for pal applications 1 1 0 i agc = 0 external agc (1) 1 1 1 v agc = 3.5v loop disabled (2) note 1: the tuner internal agc current sources are disabled note 2: the tuner internal agc detector is disabled. with no external agc voltage applied to the tuner, the rf-gain is always set to maximum. i 2 c-bus data format , ' read ' - mode: name msb lsb address byte 1 1 0 0 0 ca1 ca0 r/w=1 a status byte por fl 1 1 agc 0 0 0 a a : acknowledge ca1 / ca0 = chip address (see address selection table) por = power-on-reset-flag ; por = 1 after power-on fl = in-lock-flag ; fl = 1 when pll is phase locked agc = internal agc flag ; agc = 1 when internal agc is active
philips rf solutions objective specification 15 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 default settings of tuner pll at power-on reset: name byte msb lsb addressbyte 1 1 1 0 0 0 ca1 ca0 0 prog. divider byte 1 2 0 x x x x x x x prog. divider byte 2 3 x x x x x x x x control data byte 4 1 1 0 0 1 x x 1 switchport byte 5a 0 0 0 0 0 0 0 0 auxiliary byte (*) 5b 0 0 1 0 0 0 0 0 x = don?t care telegram examples: start ? addressbyte ? divider byte1 ? divider byte 2 ? control byte ? switchport byte - stop start ? addressbyte ? divider byte1 ? divider byte 2 ? control byte ? auxiliary byte - stop start ? addressbyte ? divider byte1 ? divider byte 2 ? stop start ? addressbyte ? control byte ? switchport byte ? stop start ? addressbyte ? control byte ? auxiliary byte ? stop i 2 c-bus timing: start stop 11 ca1ca0r/w chip address ack. ack. ack. ack. ack. 1. byte 2. byte 3. byte 4. byte sda: scl: . .
philips rf solutions objective specification 16 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 -90.0 -80.0 -70.0 -60.0 -50.0 -40.0 -30.0 -20.0 -10.0 0.0 3.50 3.00 2.50 2.00 1.50 1.00 0.50 0.00 gain control voltage at terminal 9 [v] gain reduction [db] max. if-output level : for analog, pal applications it is advisable to set the internal rf-gain control loop take over point to: al2, al1, al0 = 1, 0, 1 max. permissible if-load impedance: the max. load applied to the ' broadband ' if-output of the tuner should not exceed: 1k ? min.//15pf max. the reactive load has to be compensated (tuned-out to the if-center frequency) by an inductance connected in parallel to the load. the max. load applied to the ' narrowband ' balanced if-output of the tuner is limited to 1k ? min. . gain control characteristic of if-amplifier (terminal 9) : internal if-agc circuit 1 k v d 3 3 0 r 1 n f i f - a m p l i f i e r t e r m i n a l 9 . . . .
philips rf solutions objective specification 17 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 external rf-gain control voltage and tuner supply voltage; recommended schematic phase noise, i 2 c bus traffic and crosstalk the low noise pll used in these tuners will clean up the noise spectrum of the vcos close to the carrier to reach noise levels @ 1 khz offset from the carrier compatible with e.g. ofdm reception. linked to this noise improvement, some disturbances may become visible while they were not visible because they were hidden into the noise in analog dedicated applications and circuits. this is especially true for disturbances coming from the i 2 c bus traffic, whatever this traffic is intended for the mopll or for another slave on the bus. to avoid this i 2 c bus crosstalk and be able to have a clean noi se spectrum, it is nec essary to use a bus gate that enables the signal on the bus to drive t he mopll. this is used only when the communication is intended for the tuner part (such a kind of i 2 c bus gate is included into the philips terrestrial channel decoders), and to avoid un necessary repeated sending of the same information. main board recommendations : the tracks on the main board connected to the tuners' terminals should be kept as short as possible in order to avoid interferences because of immunity pr oblems and/or to avoid problems with regard to radiation of the local oscillator. for tuners with antenna-power function (tuners with type name extension ?p?) attention: tuners with type name extension 'p' do have the dc -supply option through out the rf-input connector on board. the max. permissible current drive is limited to 100ma . v v=+5v agc tu s s z z = 200ohms max. 100uf 3.5v = max. gain 0v = min. gain . . . . .
philips rf solutions objective specification 18 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 packaging info the products are packed in the carton box and tr ansferred to customers by pallet transport. iec types dimension b x w x h (cm) no. of sets gross wt (kg) carton 46 x 34 x 12.2 98 4.1 pallet 120 x 105 x 105 7742 345.1 carton boxes are made of corrugated fibreboard which are free of environmentally banned substances. example of carton box: w b h
philips rf solutions objective specification 19 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 mechanical dimensions general tolerances 0.5mm unless otherwise stated / all dimensions in millimeter / drawings not to scale . . . .
philips rf solutions objective specification 20 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 . . . .
philips rf solutions objective specification 21 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 . . . .
philips rf solutions objective specification 22 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 14.8 12.3 8.0 11.0 9.53 8.0 . . . . iec female iec male rf-connector data; rf-input is standard iec female; rf-output is standard iec male:
philips rf solutions objective specification 23 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 document revision history date document status rev. no. revised by revision details 03.05.2005 objective spec. a y.kalafat first draft
philips rf solutions objective specification 24 rev a : 03.05.2005 tuner modules for analog and digital terrestrial (ofdm) applications td1300a ( l ) f-3 definitions data sheet status objective specification this data sheet contains ta rget or goal specifications for product development. preliminary specification this data s heet contains preliminary data; supple mentary data may be published later. product specification this data sheet c ontains final product specification. application information where application information is given, it is ad visory and does not form part of the specification life support applications these products are not designed for use in life suppor t appliances, devices, or systems where malfunction of these products can reasonably be expected to re sult in personal injury. philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips for any damages resulting from such improper use or sale. purchase of philips i 2 c components rf solutions sales offices refer to : internet : www.rfsolutions.philips.com ? philips electronics n.v. 2005. all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does no t form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. public ation thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. purchase of philips i 2 c components conveys a license under the philips i 2 c patent to use the components in the i 2 c systems to the i 2 c specification defined by philips. this specification can be ordered using the code 9398 393 40011.

▲Up To Search▲

Price & Availability of TD1311AF

	To Download TD1311AF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .